162 lines
8.1 KiB
INI
162 lines
8.1 KiB
INI
; ===========================================================================
|
|
; hardware.ini - what this machine IS.
|
|
;
|
|
; Written once when the tower is assembled. Changing anything here means the
|
|
; hardware itself changed: a different board, a sensor fitted or removed, a
|
|
; cable moved to another port. Operational settings you tune to get better
|
|
; images - capture interval, camera profiles, scan grid, output paths - live in
|
|
; config.ini instead, and so does calibration, which is redone from time to time.
|
|
;
|
|
; WHERE THIS FILE GOES
|
|
; /etc/fire_gimbal_control/hardware.ini
|
|
;
|
|
; That is beside credentials.env, and it is deliberately OUTSIDE the directory
|
|
; deploy.sh rsyncs: a deploy cannot overwrite or delete what it never touches.
|
|
; The program looks, in order, at:
|
|
; --hardware <path> | $FGC_HARDWARE | /etc/... | beside config.ini
|
|
;
|
|
; Keys here override the same keys in config.ini, and any that are still set in
|
|
; both are named in a warning at startup so the stale copy can be deleted.
|
|
; ===========================================================================
|
|
|
|
; --- Which computer -------------------------------------------------------
|
|
[Board]
|
|
; Free-form, but keep it matching a directory under hardware/ so the setup kit
|
|
; for this board is easy to find.
|
|
model = lattepanda-3-delta
|
|
; PlatformIO env used to build the motor firmware for this board's MCU.
|
|
; lattepanda-3-delta / sigma -> leonardo (ATmega32U4, 5V logic)
|
|
; lattepanda-iota -> iota_rp2040 (RP2040, 3.3V logic)
|
|
firmware_env = leonardo
|
|
|
|
; --- What is fitted -------------------------------------------------------
|
|
; This is a DECLARATION, and its whole purpose is that startup can compare it
|
|
; with what it actually finds. The program already copes gracefully when a part
|
|
; is missing - the pitch axis, the IMU, the ambient sensor - which is correct for
|
|
; a rig built without them, and indistinguishable from a fault on a rig that has
|
|
; them. Saying what was assembled is what tells those two apart.
|
|
[Hardware]
|
|
; Axes this gimbal has. A yaw-only rig says: axes = yaw
|
|
axes = yaw, pitch
|
|
; Orientation sensor: a model name, or 'none'. Most of the fleet has none.
|
|
;
|
|
; Naming a model here is what ENABLES it - there is no second key to remember.
|
|
; [Features] enable_imu still exists for towers with no hardware.ini, but where
|
|
; this file declares a sensor the declaration wins, and a flag contradicting it
|
|
; is warned about and ignored.
|
|
imu = none
|
|
; Ambient temperature/humidity sensor: a model name, or 'none'. Same rule.
|
|
env = sht41
|
|
; The [Camera.<name>] blocks expected to be present and found.
|
|
cameras = rgb
|
|
;
|
|
; What happens when this does not match the rig:
|
|
; declared but absent -> warned about by name, and with [Features]
|
|
; strict_presence = 1 in config.ini the program refuses
|
|
; to start (exit 3). --degraded starts it anyway.
|
|
; found but undeclared -> warned about as a stale file. Never fatal.
|
|
; A tower with no hardware.ini at all is never reconciled, whatever
|
|
; strict_presence says: gaining this file must not change how a tower behaves.
|
|
|
|
; --- Where to find it -----------------------------------------------------
|
|
; Device bindings. These follow the hardware, not the tower, so they belong here
|
|
; rather than in config.ini.
|
|
|
|
[Serial]
|
|
; The motor controller MCU. Prefer the stable by-id symlink over /dev/ttyACM0,
|
|
; which is assigned in enumeration order and moves when USB devices change.
|
|
; Leonardo : /dev/serial/by-id/usb-Arduino_LLC_Arduino_Leonardo-if00
|
|
device = /dev/serial/by-id/usb-Arduino_LLC_Arduino_Leonardo-if00
|
|
baud = 115200
|
|
|
|
[IMU]
|
|
; Only read when [Hardware] imu is not 'none'. On the LattePanda 3 Delta the MTi
|
|
; is on the RS-232 header, which is a hardware UART: a stable /dev/ttyS* node,
|
|
; NOT a USB device and NOT /dev/ttyUSB0-3 (those are the modem).
|
|
device = /dev/ttyS0
|
|
|
|
[Env]
|
|
; Only read when [Hardware] env is not 'none'. This is the board's OWN native
|
|
; I2C bus, not the motor controller's serial link. The bus number varies by
|
|
; board - it is /dev/i2c-2 on the 3 Delta, not the /dev/i2c-1 default.
|
|
;
|
|
; Two traps when finding it: i2cdetect false-negatives on the SHT4x (probe with
|
|
; a real measurement instead), and an SMBus-only adapter can never work at all
|
|
; (i2cdetect -F N reports 'I2C = no').
|
|
i2c_device = /dev/i2c-2
|
|
i2c_addr = 0x44
|
|
|
|
; --- What it is made of ---------------------------------------------------
|
|
; The drivetrain, one block per axis. A different motor, gearbox or driver board
|
|
; changes these; nothing an operator tunes belongs here.
|
|
[Motor.yaw]
|
|
; Sense resistor fitted to THIS axis's TMC5160 board. It is what makes the
|
|
; milliamp figures below mean anything, which is why the host - not the firmware -
|
|
; converts them into GLOBALSCALER/IRUN register values and sends those.
|
|
r_sense_ohm = 0.075
|
|
; Milliamps RMS per phase. run_current_ma is normal motion; homing_current_ma
|
|
; applies ONLY while hunting for an endstop.
|
|
;
|
|
; The two differ when the stop cannot survive full torque. On the IOTA tower the
|
|
; endstop is a screw head meeting another screw head, and the high gear ratio let
|
|
; the motor shear one past the other - it ran 1.8 turns past the stop without the
|
|
; encoder ever falling behind. At 189 mA it homes against the same screw cleanly.
|
|
;
|
|
; The startup log prints what the registers ACTUALLY deliver, which is not
|
|
; always what you asked for; believe the log, not this file.
|
|
run_current_ma = 756
|
|
homing_current_ma = 200
|
|
; Mechanical angle between the hard endstops. A NAMEPLATE FACT: homing measures
|
|
; the travel in counts, and dividing by this yields [Motor] yaw_counts_per_deg in
|
|
; config.ini, offered for saving at the y/n prompt.
|
|
;
|
|
; Deliberately a different key, in a different file, from counts_per_deg itself:
|
|
; hardware.ini is merged OVER config.ini and wins, so sharing a key would
|
|
; silently discard every calibration the save path writes back.
|
|
;
|
|
; ROUGH until somebody measures it. Every bearing inherits its error
|
|
; proportionally, until 'gimbal heading setup' supersedes it with a landmark fit.
|
|
travel_deg = 340
|
|
; Production move speed, IN DEGREES PER SECOND - not VMAX.
|
|
;
|
|
; A register value is not portable: VMAX 30000 is 21.8 deg/s on the Delta fleet
|
|
; and 6.0 deg/s on the IOTA, because their gear ratios differ by 3.6x. Both were
|
|
; carrying the same literal, which is how two towers ended up sweeping at
|
|
; completely different speeds while their configs looked identical.
|
|
;
|
|
; The host converts through yaw_counts_per_deg and sends SPEED after each home,
|
|
; so this follows the calibration automatically. An axis whose scale is not
|
|
; trustworthy is left on the firmware's default and the reason is logged.
|
|
scan_speed_deg_s = 8.0
|
|
; The other two motions, also in deg/s. Both happen BEFORE the first home, so
|
|
; they cannot use the counts_per_deg that homing derives - they convert through
|
|
; the scale this file implies (steps_per_rev / travel_deg), which on the IOTA
|
|
; agrees with the measured one to 0.25%.
|
|
homing_speed_deg_s = 2.0
|
|
center_speed_deg_s = 6.0
|
|
|
|
; --- Told to the firmware, which holds none of it itself --------------------
|
|
; The config handshake (docs/configuration.md): the firmware asks with NEED and
|
|
; these answer it. A key missing here leaves that axis in NEEDCFG, refusing to
|
|
; move, with the missing name logged - deliberately, because a drivetrain value
|
|
; guessed by the firmware is the duplication this removes.
|
|
;
|
|
; Expected full mechanical travel, IN COUNTS. Measured, not derived: it is the
|
|
; only guard against a PHANTOM endstop - too little homing current and the motor
|
|
; stalls on ordinary friction, trips the same latch a real stop does, and the
|
|
; bogus limit is accepted.
|
|
steps_per_rev = 1210778
|
|
; |XACTUAL - XENC| that means "position untrustworthy". Re-measure whenever the
|
|
; homing current changes: the free-running gap is coupled to it.
|
|
enc_deviation = 1500
|
|
; TMC SW_MODE - physical endstop switches on REFL/REFR. Yaw on this rig homes by
|
|
; StallGuard with no switches (0); an axis with real switches sets the bits.
|
|
sw_mode = 0
|
|
; Is this axis's encoder aligned to XACTUAL and usable for hold and DIAG?
|
|
has_encoder = true
|
|
|
|
[Camera.rgb]
|
|
; The serial of the physical camera fitted to this tower. A USB DEV_ id, or a
|
|
; GigE IP address.
|
|
id = DEV_1AB22C049CD1
|